Amplifier Timer Electronic Circuit Diagram

Amplifier Timer Electronic Circuit Diagram

Reviewed by: Callie

On: 13 Jun, 2016

Viewed:1,165 times - 12 hour, 21 minute, 41 second ago

Downloaded: 0 times -

Category: Audio

Amplifier Timer Electronic Circuit Diagram Rating:
4.2
14 out of 100 based on 199 user ratings

This circuit turns-off an amplifier or any other device when a low level audio signal fed to its input is absent for 15 minutes at least.
Pushing P1 the device is switched-on feeding any appliance connected to SK1. Input audio signal is boost...

This circuit turns-off an amplifier or any other device when a low level audio signal fed to its input is absent for 15 minutes at least.
Pushing P1 the device is switched-on feeding any appliance connected to SK1. Input audio signal is boosted and squared by IC2 A & B and monitored by LED D4. When D4 illuminates, albeit for a very short peak, IC3 is reset and restarts its counting. Pin 2 of IC3 remains at the low state, the two transistors are on and the relay operates. When, after a 15 minutes delay, no signal appeared at the input, IC3 ends its counting and pin 2 goes high. Q1 & Q2 stop conducting and the relay switches-off. The device is thus completely off as also are the appliances connected to SK1. C5 & R9 reset IC3 at power-on. P2 allows switch-off at any moment.

Parts:
R1,R8 1K 1/4W Resistors
R2,R3 4K7 1/4W Resistors
R4 22K 1/4W Resistor
R5 4M7 1/4W Resistor
R6,R9 10K 1/4W Resistors
R7 1M5 1/4W Resistor
R10 100K 1/4W Resistor
R11 15K 1/4W Resistor
R12 10M 1/4W Resistor
R13 1M 1/4W Resistor
R14 8K2 1/4W Resistor
R15 1K8 1/4W Resistor
C1 470?F 25V Electrolytic Capacitor
C2,C3,C6 100nF 63V Polyester Capacitors
C4,C5 10?F 25V Electrolytic Capacitors
D1 Diode bridge 100V 1A
D2,D7 1N4002 100V 1A Diodes
D3 Red LED 5mm.
D4 Yellow LED 5mm.
D5,D6 1N4148 75V 150mA Diodes
IC1 78L12 12V 100mA Voltage regulator IC
IC2 LM358 Low Power Dual Op-amp
IC3 4060 14 stage ripple counter and oscillator IC
Q1 BC557 45V 100mA PNP Transistor
Q2 BC337 45V 800mA NPN Transistor
J1 RCA audio input socket
P1 SPST Mains suited Pushbutton
P2 SPST Pushbutton
T1 220V Primary, 12V Secondary 3VA Mains transformer
RL1 10.5V 270 Ohm Relay with SPST 5A 220V switch
PL1 Male Mains plug
SK1 Female Mains socket

Notes:
Simply connect left or right channel tape output of your amplifier to J1.
You can employ two RCA input sockets wired in parallel to allow pick-up audio signals from both stereo channels.
The delay time can be varied changing R13 and/or C6 values.
Needing to operate a device not supplied by power mains, use a double pole relay switch, connecting the second pole switch in series with the device's supply.

Related Posts

Motorola Hi Fi Power Amplifier Electronic Circuit Diagram

This is a very simple, low cost, Hi-Fi quality power amplifier. You can build it 5 ways, like itÂ’s shown in the table (from 20 W to 80 W RMS).

  • The first thing that you must do, is t...

Amplified Ear Electronic Circuit Diagram

This circuit, connected with 32 Ohms impedance mini-earphones, can detect very remote sounds. Useful for theatre, cinema and lecture goers: every word will be clearly heard. You can also listen to ...

Fet Audio Mixer Electronic Circuit Diagram

How to build FET Audio Mixer

This simple circuit mixes two or more channels into one channel (eg. stereo into mono). The circuit can mix as many or as few channels as you ...

25W Mosfet Audio Amplifier Electronic Circuit Diagram

This is high fidelity, high quality 25W HiFi audio amplifier circuit delivers great audio performance. You don’t need pre amplifier circuit for this design since it can be directly connected ...

Portable Headphone Amplifier Electronic Circuit Diagram

Portable Headphone Amplifier Circuit Based 3 Transistors

his simple headphone amplifier circuit can be directly connected to other compact devices such as CD player, W...

Op Amp Microphone Preamp Electronic Circuit Diagram

A high quality microphone preamplifier using a single power supply, suitable for dynamic or electret microphones. The op-amp used can be any low noise, high performance type, e.g. NE5534,TL071, OPA...

As the fastest growing demand of circuit and wiring diagram for automotive and electronics on internet based on different uses such as electronic hobbyists, students, technicians and engineers than we decided to provide free circuit and wiring diagram base on your needed.

To find circuit and wiring diagram now a day its easy. E-learning through internet as a right place to search an exact circuit and wiring diagram of your choice and it's much fun and knowledgable. On internet you will find thousands of electronic circuit diagrams some are very good designed and some are not. So you have to modify them to make them according to your needs but some circuits are ready to make and require no changes.

There are many categories of circuit and wiring diagrams like automotive, audio circuits, radio & RF circuits, power supply circuits, light circuits, telephone circuits, timer circuits, battery charger circuits etc. There are many types of circuit and wiring diagrams some are very easy to build and some are very complicated, some are so small and some contain huge list of parts.

We provides free best quality and good designed schematic diagrams our diagrams are free to use for all electronic hobbyists, students, technicians and engineers. We also provides a full educational system to students new to electronics. If you are new to electronics you are a student or a electronic hobbyist and want to increase your knowledge in electronics or want to understand electronics in a very easy way so this is the right place for you we provide electronics beginner guide tutorials to easily understand complicated electronic theory. Our mission is to help students and professionals in their field.